British steam railcars

Origins

The first steam railcar was designed by James Samuel, the Eastern Counties Railway Locomotive Engineer, built by William Bridges Adams in 1847, and trialled between Shoreditch and Cambridge on 23 October 1847. An experimental unit, 12 feet 6 inches (3.81 m) long with a small vertical boiler and passenger accommodation was a bench seat around a box at the back, although it was officially named Lilliputian it was known as Express.

The following year Samuel and Adams built the Fairfield steam carriage. This was much larger, 31 feet 6 inches (9.60 m) long, and built with an open third class section and a closed second class section. After trials in 1948, it was sold to the Bristol & Exeter Railway and adapted for the 7-foot gauge and the body rebuilt to seat 16 in first-class and 32 in second-class. It ran for two years on the Tiverton branch before the engine was converted to a 0-4-0 locomotive.

Enfield, combining a contemporary designs of engine and carriage, was larger still. Built by Samuel and Adams this was used in regular service by the Eastern Counties Railway until the engine was converted into a 2-2-2 tank locomotive. More engine and carriage combinations to Samuel designs were built in the 1850s in the Eastern Counties railway works, and another by Kitson & Co. called Ariel's Girdle. Later, in 1869, Samuel, Robert Fairlie and George England collaborated to build a prototype articulated steam railcar at England's Hatcham Ironworks that was demonstrated in the works yard. However, England went out of business at about this time and nothing is known about the fate of this vehicle.

Design

The steam railcar was revived in 1902 when Dugald Drummond of the London & South Western Railway (L&SWR) built two for a branch line near Portsmouth. Steam railcars were introduced for two main reasons, either to compete with the new electric tramways that were abstracting traffic away in suburban areas or to provide an economic service on lightly used country branch lines. To allow for inexpensive low-level halts steps were provided, interlocked with the brakes so the train could not move with them extended.

There were two main designs, either with a powered bogie enclosed in a rigid body, or the engine unit and carriage were articulated, pivoting on a pin. The steam boiler could be enclosed or left open and was generally open on the articulated units and enclosed on the rigid bodies. Higher maintenance requirements of the engine meant some companies had more locomotive units than carriages.

The steam railcar had a driving position at both ends so it could run in either direction without been turned, or for a locomotive to run round its carriages at a terminus. Control from the rear end was normally by a wheel connected to the regulator by a continuous wire in or above the roof space or a rod running under the floor. The driver was provided with brake and whistle controls, and some means of communicating with the fireman, who stayed on the footplate. This was normally by a bell code and required a 'passed fireman' who was qualified to act as driver. Unpowered carriages could also be attached and some had control equipment.

With passenger accommodation in open saloons, the units were usually vacuum braked, steam heated and provided with gas lighting, although electric lighting was fitted to some units. However, there was little reserve power for additional carriages and therefore the cars were inflexible and, especially on the articulated types, the ride quality was poor due to excessive vibration and oscillation. Most steam railcars were replaced by an autotrain, a push-pull steam locomotive and carriages.

London & South Western Railway

To provide an economic service on the L&SWR and London, Brighton & South Coast Railway (LB&SCR) joint branch from Fratton to Southsea two steam railmotors were built by the L&SWR in 1902. The 43-foot (13 m) long carriage seated 30 in third class and 12 in first class and the total length of the vehicle was 53 ft 5 in (16.28 m). The first unit was lent to the Great Western Railway, returning with favourable reports. However, when introduced in summer 1903 the units struggled with passengers on the gradients on the line and it was discovered that the GWR had trialed the unit on level track and without passengers. The units were rebuilt with a bigger firebox and boiler.

These were followed by fifteen more railmotors for the L&SWR system. The first two were built in 1904, the engines at Nine Elms and the carriages at Eastleigh. Two feet (600 mm) shorter than the earlier cars, these seated eight in first class and thirty-two in third. Thirteen more were built in 1905–6 to slightly different design and with the boiler pressure increased from 150 psi (1.0 MPa) to 175 psi (1.21 MPa). Engines and carriages were not detachable and these units were capable of towing an additional carriage. After the outbreak of World War I limited the work available for railmotors the joint stock was taken out of service in 1914 and by 1916 only three units remained in service, to be withdrawn in 1919.

Great Western Railway

After the trials with the L&SWR railmotor, in 1903 the GWR designed and built two prototypes and by 1908 had 99 carriages and 112 engine units. Although there were detail differences between carriages there were six basic types: the prototypes were the only examples 57 feet (17 m) long and in 1905 two railmotors (numbered 15 and 16) arrived from Kerr, Stuart & Co. These were unlike the others, of the articulated type and to the outline design of Tom Hurry Riches of the Taff Vale Railway but with locomotive style boilers. The other carriages were either 59 feet 6 inches (18.14 m) or 70 feet (21 m) long and designed for branch or suburban use, the branch cars having a separate lugguage compartment. There were between 49 and 64 seats and two cars had corridor connections at both ends.

The engines, apart for the two for the Kerr, Stuart cars, were all interchangeable, although there were minor differences in the heating surface, wheel diameter and tractive effort. These were equipped with a swing arm suspension that was effective in damping out the vibration typical of steam railcars.

Withdrawals started in 1914, services being replaced by autotrains. Three were sold and one was destroyed in a fire but most were converted into trailers. However, by the 1923 grouping 53 remained in service and it was October 1935 before they were all withdrawn.

As of 2012 a reconstructed GWR steam railmotor built in 1908 is operational and based at Didcot Railway Centre.

Taff Vale Railway

Riches, the Taff Vale Railway's locomotive engineer, designed in 1903 the first articulated railmotor with the boiler unusually placed across the frames with a single firebox and two short drums, this giving a high steam raising capacity. The engine unit and carriage pivoted on a pin, and the two parts could be separated in twenty minutes. The carriage had a third class saloon for 40 passengers and a first class compartment for 12 and an open rear driving position. This was followed by fifteen more: six in 1904, the engines built by Avonside Engine Co. and another six from Kerr, Stuart & Co. in 1905. The carriages built by the Bristol Wagon & Carriage Co. were similar to the prototype except the open end was enclosed. In 1906 five engines were built by Manning Wardle & Co.; these were larger with entrances front and rear. Only three longer 53 feet 3 inches (16.23 m) carriages were purchased that year, allowing two spare engines for maintenance.

The railcars worked over most of the Taff Vale system, normally without a trailer. The carriages began to be converted into autocoaches from 1914 and all withdrawn by the early 1920s.

Lancashire and Yorkshire Railway

In 1905 the Lancashire and Yorkshire Railway (L&YR) received two railmotors from Kerr, Stuart similar to those they had supplied to the Taff Vale Railway. The carriages were built by the L&YR at Newton Heath on an under-frame built by Kerr, Stuart and seated 48 passengers in third class. The railmotors were considered underpowered by L&YR and soon the cylinders were bored out and fitted with new pistons.

As the requirement was to work with a trailer, George Hughes, the L&YR locomotive engineer redesigned the cars. Retaining the articulated concept, the engine units were given a larger locomotive style boiler and four coupled wheels giving a tractive effort of 8,080 lbf (35.9 kN). The carriage bodies seated 56 passengers and had corridor connections. Eighteen engine units and sixteen carriages were built between 1906 and 1911, the two original engines being withdrawn and replaced by ones of the new style in 1909. Twelve trailers, fitted with controls, were built. Being of the articulated type the ride quality was poor.

All eighteen were running when the L&YR were absorbed into the London, Midland and Scottish Railway (LMS) in the 1923 grouping, the first being withdrawn in 1927 and one was still running when the railways were nationalised in 1948.

Other railways

In 1904 and 1905 the South Eastern & Chatham Railway purchased eight articulated steam railcars for the Sheppey Light Railway and the Hundred of Hoo Railway, seating 56 in third class. They were withdrawn in 1914, replaced by push-pull trains and SECR Class P 0-6-0 tanks. Between 1905 and 1907 the London & North Western Railway built six rigid steam railcars with a powered bogie that could be removed via double doors at the front end. Passenger accommodation was 48 in third class, the cars were fitted with electric lighting, and there was electric bell communication from the rear driving position and the footplate. All six were absorbed into the LMS fleet in 1923 and one, no. 3, survived to be nationalised, being withdrawn in February 1948. The Great Northern Railway (GNR) had eight railmotors built in 1905, two were petrol driven and unsuccessful and six were articulated steam railcars. Built in pairs by different manufacturers to compare performance, no further units were built. The six steam railcars were absorbed into the London & North Eastern Railway in the 1923 grouping and withdrawn in 1925 and 1926.

Between 1903 and 1911 a total of 23 railcars were introduced by another thirteen railway companies.

Early examples

Other railcars used steam motors, high speed steam engines together with a form of gearing. In 1905 a four-wheeled vehicle was designed for the Kent & East Sussex Railway and built by RY Pickering. This could seat 31 passengers and suffered poor ride quality and was taken out of use but was on the stock list when the railway was nationalised in 1948. Ganz of Budapest had designed a geared steam car and the Peebles Steam Car Co. was formed to promote the car in Britain with suggestions that the Hungarian Government Railway had purchased 300 units. Steam was raised at 300 psi (2.1 MPa) and supplied to a 35 hp (26 kW) two cylinder engine. In 1905 a prototype was built and two trial runs were made. It was reported that the ride quality was smooth, but the acceleration was moderate and the maximum speed was about 30 mph (48 km/h). No orders were placed and the steam car was shipped to the continent.

In 1923 Sentinel Waggon Works and Cammell Laird collaborated to build a prototype lightweight steam rail car for the Jersey Railway. A range of Sentinel–Cammell railcars were developed with a choice of a single car or an articulated pair and a 100 hp (75 kW) motor or 200 hp (150 kW) with one boiler and two motors. A total of 290 were built for customers worldwide, 91 for use in Britain A boiler raised steam at 300 to 350 psi (2.1 to 2.4 MPa), feeding one or two steam motors. The first steam motors had two cylinders as were used on contemporary steam lorries but by 1925 a 6-cylinder version had been developed. In the early units chains were used in final drive until a gearbox and cardan shaft drive was developed in 1927. In the early units the engine unit was articulated, enclosed in similar coachwork to the passenger section; the whole car was made of steel.

A car was shown at the British Empire Exhibition in 1924 and 1925 and tested by the LNER. To provide a better service to compete with raising levels of road traffic two of these articulated 100 hp (75 kW) two-cylinder chain-driven units were purchased, and operated in the Lowestoft area. This was followed by 22 cars to a similar design in 1927 and 1928. A prototype cardan shaft driven car with a rigid body was built in 1927 and between 1928 and 1930 forty-nine cars with six cylinder cardan shafts drives and rigid bodies were purchased, followed by five 200 hp (150 kW) cars in 1930 and 1932 and Phenomena, a twin articulated pair with two 100 hp six cylinder motors, in 1930. This could seat 39 in the power car and 83 in the trailer. Between 1927 and 1943 a number were allocated to Heaton shed, near Newcastle upon Tyne, and operated to Blackhill and over the Tyne Valley Line to North Wylam and Prudhoe. On 9 June 1929, railcar No. 220 Waterwitch overran signals at Marshgate Junction, Doncaster and was consequently in collision with an excursion train. The railcar was cut in two. It was not repaired.

The London, Midland and Scottish (LMS) also purchased a prototype in 1925, followed by twelve in 1927 and a single six-cylinder car in 1928. The LNER had a joint interest in the Cheshire Lines Railway and the Axholme Joint Railway, and they purchased four cars and one car respectively. A lightweight railbus was built for the Southern Railway in 1933 and seated 44 passengers, was 48 ft 4 in (14.73 m) long and weighed 17 long tons 4 cwt (38,500 lb or 17.5 t). However, its frame broke when heavily overloaded in 1935 and although repaired, it was withdrawn in 1936.

Most of the LMS railcars were withdrawn in 1935, the last being the six-cylindered car, this being withdrawn in December 1936. The last LNER Sentinel railcar was withdrawn in 1947.

Clayton

In 1927 a prototype steam railcar was built by Clayton Wagons Ltd for the LNER. This was similar to the earlier Sentinel-Cammell cars, but with the coal bunker was outside the car on the powered bogie. A further ten were delivered in 1928, six new to the Heaton shed, later joined by seventh. One car was delivered in the teak LNER coach livery, but painted red and cream in February 1929; the others arrived in this livery. The railcars worked services to Morpeth, Leamside and Blackhill. One car was withdrawn in 1932, one was transferred to Norwich in 1935 and the other five were withdrawn in 1936. All railcars had been withdrawn by 1937.