Mineral physics

Shock compression

Many of the pioneering studies in mineral physics involved explosions or projectiles that subject a sample to a shock. For a brief time interval, the sample is under pressure as the shock wave passes through. Pressures as high as any in the Earth have been achieved by this method. However, the method has some disadvantages. The pressure is very non-uniform and is not adiabatic, so the pressure wave heats the sample up in passing. The conditions of the experiment must be interpreted in terms of a set of pressure-density curves called Hugoniot curves.

Multi-anvil press

Multi-anvil presses involve an arrangement of anvils to concentrate pressure from a press onto a sample. Typically the apparatus uses an arrangement eight cube-shaped tungsten carbide anvils to compress a ceramic octahedron containing the sample and a ceramic or Re metal furnace. The anvils are typically placed in a large hydraulic press. The method was developed by Kawai and Endo in Japan. Unlike shock compression, the pressure exerted is steady, and the sample can be heated using a furnace. Pressures of about 28 GPa (equivalent to depths of 840 km), and temperatures above 2300 °C, can be attained using WC anvils and a lanthanum chromite furnace. The apparatus is very bulky and cannot achieve pressures like those in the diamond anvil cell (below), but it can handle much larger samples that can be quenched and examined after the experiment. Recently, sintered diamond anvils have been developed for this type of press that can reach pressures of 90 GPa (2700 km depth).

Diamond anvil cell

The diamond anvil cell is a small table-top device for concentrating pressure. It can compress a small (sub-millimeter sized) piece of material to extreme pressures, which can exceed 3,000,000 atmospheres (300 gigapascals). This is beyond the pressures at the center of the Earth. The concentration of pressure at the tip of the diamonds is possible because of their hardness, while their transparency and high thermal conductivity allow a variety of probes can be used to examine the state of the sample. The sample can be heated to thousands of degrees.

Creating high temperatures

Achieving temperatures found within the interior of the earth is just as important to the study of mineral physics as creating high pressures. Several methods are used to reach these temperatures and measure them. Resistive heating is the most common and simplest to measure. The application of a voltage to a wire heats the wire and surrounding area. A large variety of heater designs are available including those that head the entire diamond anvil cell (DAC) body and those that fit inside the body to heat the sample chamber. Temperatures below 700°C can be reached in air due to the oxidation of diamond above this temperature. With an argon atmosphere, higher temperatures up to 1700°C can be reached without damaging the diamonds. Resistive heaters have not achieved temperatures above 1000°C.

Laser heating is done in a diamond-anvil cell with Nd:YAG or CO2 lasers to achieve temperatures above 6000k. Spectroscopy is used to measure black-body radiation from the sample to determine the temperature. Laser heating is continuing to extend the temperature range that can be reached in diamond-anvil cell but suffers two significant drawbacks. First, temperatures below 1200°C are difficult to measure using this method. Second, large temperature gradients exist in the sample because only the portion of sample hit by the laser is heated.

Equations of state

To deduce the properties of minerals in the deep Earth, it is necessary to know how their density varies with pressure and temperature. Such a relation is called an equation of state (EOS). A simple example of an EOS that is predicted by the Debye model for harmonic lattice vibrations is the Mie-Grünheisen equation of state:

where C V is the heat capacity and γ D is the Debye gamma. The latter is one of many Grünheisen parameters that play an important role in high-pressure physics. A more realistic EOS is the Birch–Murnaghan equation of state.

Interpreting seismic velocities

Inversion of seismic data give profiles of seismic velocity as a function of depth. These must still be interpreted in terms of the properties of the minerals. A very useful heuristic was discovered by Francis Birch: plotting data for a large number of rocks, he found a linear relation of the compressional wave velocity v p of rocks and minerals of a constant average atomic weight M ¯ with density ρ :

This relationship became known as Birch's law. This makes it possible to extrapolate known velocities for minerals at the surface to predict velocities deeper in the Earth.

Other physical properties

Methods of crystal interrogation

There are a number of experimental procedures designed to extract information from both single and powdered crystals. Some techniques can be used in a diamond anvil cell (DAC) or a multi anvil press (MAP). Some techniques are summarized in the following table.

First principles calculations

Using quantum mechanical numerical techniques, it is possible to achieve very accurate predictions of crystal's properties including structure, thermodynamic stability, elastic properties and transport properties. The limit of such calculations tends to be computing power, as computation run times of weeks or even months are not uncommon.