Rusty bolt effect - Alchetron, The Free Social Encyclopedia

The rusty bolt effect is radio interference due to interactions with dirty connections or corroded parts. It is more properly known as passive intermodulation, and can result from a variety of different causes such as ferromagnetic conduction metals, or nonlinear microwave absorbers and loads. Corroded materials on antennas, waveguides, or even structural elements, can act as one or more diodes. (Crystal sets, early radio receivers, used the semiconductor properties of natural galena to demodulate the radio signal, and copper oxide was used in power rectifiers.) This gives rise to undesired interference, including the generation of harmonics or intermodulation. Rusty objects that should not be in the signal-path, including antenna structures, can also reradiate radio signals with harmonics and other unwanted signals. As with all out-of-band noise, these spurious emissions can interfere with receivers.

Possible cures

If one experiences this problem, one should check both the transmitter and the receiver for dirty connections or corroded parts. One should also check for signs of corrosion in the cables which link the equipment to the antennae and for badly made joints. Beyond this, one might check any metal objects near the antenna for rust or corrosion. Any of these could be the source of the problem.

Various adjustments and modifications can mitigate or cure these problems:

Remove the corroded object. This is often the best cure.

Clean the object - if the rust is superficial, the diode behavior might be eliminated by removing the surface rust.

Place an insulator between the two objects which are causing the issue. This might reduce the RF current.

Lower the RF field strength. Intermodulation becomes much worse with amplitude, so small amplitude reduction can greatly reduce the intensity of the effect. See the mathematics section below for details.

Get a better antenna which is more directional. It may be possible to point the aerial in such a direction that it does not pick up the unwanted signal coming from the "rusty bolt."

Mathematics associated with the rusty bolt

The transfer characteristic of an object can be represented as a power series:

E out = ∑ n = 1 ∞ K n E in n

Or, taking only the first few terms (which are most relevant),

E out = K 1 E in + K 2 E in 2 + K 3 E in 3 + K 4 E in 4 + K 5 E in 5 + . . .

For an ideal perfect linear object K₂, K₃, K₄, K₅, etc. are all zero. A good connection approximates this ideal case with sufficiently small values.

For a 'rusty bolt' (or an intentionally designed frequency mixer stage), K₂, K₃, K₄, K₅, etc. are not all zero. These higher-order terms result in generation of harmonics.

The following analysis applies the power series representation to an input sine-wave.

Harmonic generation

If the incoming signal is a sine wave {E_in sin(ωt)}, (and taking only first-order terms), then the output can be written:

E out = ∑ i = 1 ∞ K i E in i sin ⁡ ( i ω t ) = K 1 E in sin ⁡ ( ω t ) + K 2 E in 2 sin ⁡ ( 2 ω t ) + K 3 E in 3 sin ⁡ ( 3 ω t ) + K 4 E in 4 sin ⁡ ( 4 ω t ) + K 5 E in 5 sin ⁡ ( 5 ω t ) + ⋯

Clearly, the harmonic terms will be worse at high input signal amplitudes, as they increase exponentially with the amplitude of E_in.

Second order terms

To understand the generation of nonharmonic terms (frequency mixing), a more complete formulation must be used, including higher-order terms. These terms, if significant, give rise to intermodulation distortion.

E f 1 + f 2 = k E f 1 E f 2 E f 1 − f 2 = k E f 1 E f 2

Third order terms

E f 1 + f 2 + f 3 = k E f 1 E f 2 E f 3 E f 1 − f 2 + f 3 = k E f 1 E f 2 E f 3 E f 1 + f 2 − f 3 = k E f 1 E f 2 E f 3 E f 1 − f 2 − f 3 = k E f 1 E f 2 E f 3

Hence the second-order, third-order, and higher-order mixing products can be greatly reduced by lowing the intensity of the original signals (f₁, f₂, f₃, f₄, …, f_n)

References

Rusty bolt effect Wikipedia

(Text) CC BY-SA