| 220 km/h|
| 13 m|
| Warsaw University of Technology, PZL-Świdnik|
The Politechnika Warszawska PW-5 Smyk (Polish: "Little rascal") is a single seater sailplane designed at the Warsaw University of Technology (Polish: "Politechnika Warszawska") and manufactured in Poland. It is a monotype World Class glider.
The PW-5 was designed for, and won a competition held by the International Gliding Commission for a simple, low cost sailplane that would form the basis for a new competition class, the IGC World Class. Unlike other soaring competition classes, the World Class designation would guarantee that all pilots participated on an equal footing, and that pilots could not gain advantage by spending large amounts of money. The PW-5 was unanimously chosen from 42 design proposals in IGC international World Class design competition. In November 1989, the IGC issued a worldwide call for proposals. By February 1990, it had received 84 requests for design specifications from 25 countries. By August 1990, the IGC had received 42 design proposals from 20 countries. In September 1990, after reviewing the proposals, many of which came with models, the IGC recommended that 11 designs from 9 countries proceed to the prototype competition. In October 1992, the IGC inspected and tested 6 prototypes from 5 countries at Oerlinghausen Germany. After further review and collecting manufacturing data, in spring 1993 the IGC declared the PW-5, designed by a faculty/student team at Warsaw University of Technology, the first World Class glider.
The glider was designed at the Faculty of Power and Aeronautical Engineering of the Warsaw University of Technology under the supervision of Roman Świtkiewicz. It was originally built by PZL at its factory in Świdnik and first flew in 1993. By the end of 2000 the new private company PZL-Bielsko1 was established by the original members of the design team from Warsaw University of Technology and the DWLKK company. A new factory at Bielsko produced a modified version of PW-5 glider called B1-PW-5.
Because its cost was comparable to the cost of the older Club class gliders of higher performance it did not sell as well as expected and the World class competitions were not very popular as well. In total fewer than 200 PW-5s have been built, though over 70 have been exported to the United States, where there is a keen following.The structure is all glass-epoxy composite
The wings are of trapeze contour with bow-shaped ends, shoulder-set on the fuselage, having a monospar structure with sandwich shells
Schempp-Hirth-type air brakes extend on the upper wing surface only
Fuselage shell of glass-epoxy composite monocoque structure, stiffened with frames
Fabric covered rudder
Fixed undercarriage consisting of main wheel behind the pilot, with shock absorber and drum brake, a smaller front wheel and a tail skid with a diminutive wheel to prevent scraping on the ground if overrotation takes place
Two tow releases, for aerotowing and winch-launching respectively
There are presently two versions of the PW-5. The Bielsko version, identified as B1 PW-5, has a few safety- and performance-related improvements:Automatic hook-up of all controls upon assembly
Tow release for winch-launching moved forward; this follows a winching accident in New Zealand
Ballast holder in the tail to allow centre of gravity corrections
Total energy probe on the vertical empennage
There is a project in progress for building a motorglider designated PW-5M based on the PW-5.
The PW-5 has a two-seater derivative, the PW-6.
General characteristicsCrew: One
Length: 6.22 m (20 ft 5 in)
Wingspan: 13.44 m (44 ft 1 in)
Height: 1.86 m (6 ft 1 in)
Wing area: 10.2 m2 (109.8 ft2)
Aspect ratio: 17.71
Empty weight: 190 kg (419 lb)
Gross weight: 300 kg (661 lb)
PerformanceMaximum speed: 220 km/h (140 mph)
Maximum glide ratio: 32
Rate of sink: 0.65 m/s (128 ft/min)