![]() | ||
Mohr–Coulomb theory is a mathematical model (see yield surface) describing the response of brittle materials such as concrete, or rubble piles, to shear stress as well as normal stress. Most of the classical engineering materials somehow follow this rule in at least a portion of their shear failure envelope. Generally the theory applies to materials for which the compressive strength far exceeds the tensile strength.
Contents
- History of the development
- MohrCoulomb failure criterion
- MohrCoulomb failure criterion in three dimensions
- MohrCoulomb failure surface in HaighWestergaard space
- MohrCoulomb yield and plasticity
- References
In geotechnical engineering it is used to define shear strength of soils and rocks at different effective stresses.
In structural engineering it is used to determine failure load as well as the angle of fracture of a displacement fracture in concrete and similar materials. Coulomb's friction hypothesis is used to determine the combination of shear and normal stress that will cause a fracture of the material. Mohr's circle is used to determine which principal stresses that will produce this combination of shear and normal stress, and the angle of the plane in which this will occur. According to the principle of normality the stress introduced at failure will be perpendicular to the line describing the fracture condition.
It can be shown that a material failing according to Coulomb's friction hypothesis will show the displacement introduced at failure forming an angle to the line of fracture equal to the angle of friction. This makes the strength of the material determinable by comparing the external mechanical work introduced by the displacement and the external load with the internal mechanical work introduced by the strain and stress at the line of failure. By conservation of energy the sum of these must be zero and this will make it possible to calculate the failure load of the construction.
A common improvement of this model is to combine Coulomb's friction hypothesis with Rankine's principal stress hypothesis to describe a separation fracture.
History of the development
The Mohr–Coulomb theory is named in honour of Charles-Augustin de Coulomb and Christian Otto Mohr. Coulomb's contribution was a 1773 essay entitled "Essai sur une application des règles des maximis et minimis à quelques problèmes de statique relatifs à l'architecture" . Mohr developed a generalised form of the theory around the end of the 19th century. As the generalised form affected the interpretation of the criterion, but not the substance of it, some texts continue to refer to the criterion as simply the 'Coulomb criterion'.
Mohr–Coulomb failure criterion
The Mohr–Coulomb failure criterion represents the linear envelope that is obtained from a plot of the shear strength of a material versus the applied normal stress. This relation is expressed as
where
If
From Mohr's circle we have
where
and
Therefore, the Mohr–Coulomb criterion may also be expressed as
This form of the Mohr–Coulomb criterion is applicable to failure on a plane that is parallel to the
Mohr–Coulomb failure criterion in three dimensions
The Mohr–Coulomb criterion in three dimensions is often expressed as
The Mohr–Coulomb failure surface is a cone with a hexagonal cross section in deviatoric stress space.
The expressions for
where
The Mohr–Coulomb failure criterion can then be evaluated using the usual expression
for the six planes of maximum shear stress.
Mohr–Coulomb failure surface in Haigh–Westergaard space
The Mohr–Coulomb failure (yield) surface is often expressed in Haigh–Westergaad coordinates. For example, the function
can be expressed as
Alternatively, in terms of the invariants
where
Mohr–Coulomb yield and plasticity
The Mohr–Coulomb yield surface is often used to model the plastic flow of geomaterials (and other cohesive-frictional materials). Many such materials show dilatational behavior under triaxial states of stress which the Mohr–Coulomb model does not include. Also, since the yield surface has corners, it may be inconvenient to use the original Mohr–Coulomb model to determine the direction of plastic flow (in the flow theory of plasticity).
A common approach is to use a non-associated plastic flow potential that is smooth. An example of such a potential is the function
where