Trisha Shetty (Editor)

World file

Updated on
Share on FacebookTweet on TwitterShare on LinkedInShare on Reddit
Covid-19

A world file is a six line plain text sidecar file used by geographic information systems (GIS) to georeference raster map images. The file specification was introduced by Esri, and consists of six coefficients of an affine transformation that describes the location, scale and rotation of a raster on a map.

Contents

Definition

The generic meaning of the six parameters in a world file (as defined by Esri) are:

  • Line 1: A: pixel size in the x-direction in map units/pixel
  • Line 2: D: rotation about y-axis
  • Line 3: B: rotation about x-axis
  • Line 4: E: pixel size in the y-direction in map units, almost always negative
  • Line 5: C: x-coordinate of the center of the upper left pixel
  • Line 6: F: y-coordinate of the center of the upper left pixel
  • This description is however misleading in that the D and B parameters are not angular rotations, and that the A and E parameters do not correspond to the pixel size if D or B are not zero. The A, D, B and E parameters are sometimes named "x-scale", "y-skew", "x-skew" and "y-scale".

    A better description of the A, D, B and E parameters are:

  • Line 1: A: x-component of the pixel width (x-scale)
  • Line 2: D: y-component of the pixel width (y-skew)
  • Line 3: B: x-component of the pixel height (x-skew)
  • Line 4: E: y-component of the pixel height (y-scale), typically negative
  • All four parameters are expressed in the map units, which are described by the spatial reference system for the raster.

    When D or B are non-zero the pixel width is given by:

    A 2 + D 2

    and the pixel height by

    B 2 + E 2

    World files describing a map on the Universal Transverse Mercator coordinate system (UTM) use these conventions:

  • D and B are usually 0, since the image pixels are usually made to align with the UTM grid
  • C is the UTM easting
  • F is the UTM northing
  • Units are always meters per pixel
  • The above description applies also to a rectangular, non-rotated image which might be, for example, overlaid on an orthogonally projected map. If the world file describes an image that is rotated from the axis of the target projection, however, then A, D, B and E must be derived from the required affine transformation (see below). Specifically, A and E will no longer be the meter/pixel measurement on their respective axes.

    These values are used in a six-parameter affine transformation:

    [ x y ] = [ A B C D E F ] [ x y 1 ]

    which can be written as this set of equations:

    x = A x + B y + C y = D x + E y + F

    where:

    x' is the calculated UTM easting of the pixel on the map y' is the calculated UTM northing of the pixel on the map x is the column number of the pixel in the image counting from left y is the row number of the pixel in the image counting from top A or x-scale; dimension of a pixel in map units in x-direction B, D are rotation terms C, F are translation terms: x, y map coordinates of the center of the upper-left pixel E is negative of y-scale: dimension of a pixel in map units in y-direction

    The y-scale (E) is negative because the origins of an image and the UTM coordinate system are different. The origin of an image is located in the upper-left corner, whereas the origin of the map coordinate system is located in the lower-left corner. Row values in the image increase from the origin downward, while y-coordinate values in the map increase from the origin upward. Many mapping programs are unable to handle "upside down" images (i.e. those with a positive y-scale).

    To go from UTM(x'y') to pixel position(x,y) one can use the equation:

    x = E x B y + B F E C A E D B y = D x + A y + D C A F A E D B

    Example: Original falknermap.jpg is 800×600 pixels (map not shown). Its world file is falknermap.jgw and contains:

    32.0 0.0 0.0 -32.0 691200.0 4576000.0

    The position of Falkner Island light on the map image is:

    x = 171 pixels from left y = 343 pixels from top

    This gives:

    x1 = 696672 meters Easting y1 = 4565024 meters Northing

    The UTM (grid) zone is not given so the coordinates are ambiguous — they can represent a position in any of the approximately 120 UTM grid zones. In this case, approximate latitude and longitude (41.2, −072.7) were looked up in a gazetteer and the UTM (grid) zone was found to be 18 using a Web-based converter.

    Filename extension

    The filename extension of the world file is based on the raster file's extension.

    One convention is to append the letter "w" to the end of the raster filename: falknermap.jpgfalknermap.jpgw.

    An alternative naming convention is also well supported. The second letter of the original filename extension is removed, and the letter "w" is added at the end. For example, falknermap.jpgfalknermap.jgw or falknermap.tiffalknermap.tfw. This convention was developed for filenames that need to conform to the 8.3 file naming convention.

    Localization

    When writing world files it is advisable to ignore localization settings and always use "." as the decimal separator. Also, negative numbers should be specified with the "-" character exclusively. This ensures maximum portability of the images.

    References

    World file Wikipedia


    Similar Topics
    Lal Bahadur Shastri (film)
    Alef (footballer)
    Mark P Fitzgerald
    Topics
     
    B
    i
    Link
    H2
    L