Power type Electric Build date 2013-2015 | Model ZELC 20E Total produced 95 | |
 | ||
Designer Zhuzhou Electric Locomotive Co. Builder Zhuzhou Electric Locomotive Co.
CSR Zhuzhou-Matsetse Basadi | ||
The Transnet Freight Rail Class 20E of 2013 is a South African electric locomotive.
Contents
In early August 2013, the first of ninety-five Class 20E dual-voltage electric locomotives for Transnet Freight Rail was lowered onto its bogies for the first time. Ten of these locomotives were built by the Zhuzhou Electric Locomotive Company in China, while the rest were built locally.
Manufacturer
The first ten of ninety-five 3 kV DC and 25 kV AC dual voltage Class 20E electric locomotives for Transnet Freight Rail were built in China by Zhuzhou Electric Locomotive Company, a subsidiary of the China South Locomotive and Rolling Stock Corporation (CSR), China's leading train manufacturer. The roll-out ceremony of the first locomotive, no. 20-001, took place at the factory in Changsha in central China's Hunan Province on 20 August 2013.
The contract marked Zhuzhou’s largest single foreign order of electric locomotives to date and made provision for the company to export electric locomotive manufacturing technologies to South Africa, to enable a local production ratio of more than 60 percent. The first two of these locomotives, numbers 20-002 and 20-003, were landed at Durban Harbour on 14 November 2013. Three more, numbers 20-001, 20-004 and 20-005, came ashore on 18 December 2013.
Of the remaining eighty-five locomotives, numbers 20-011 to 20-025 were assembled from Chinese-built kits by Transnet Engineering at Koedoespoort and were all in service by the end of September 2014.
The rest of the order has greater local content and was built at Koedoespoort in South Africa by a consortium, composed of CSR Zhuzhou and the South African Black Economic Empowerment company Matsetse Basadi. The first of these, no. 20-026, was in service by late September 2014.
Characteristics
The locomotive body is a welded monocoque design, constructed of steel plates and profiled members, which has a compressive strength of 4.45 meganewtons (1,000,000 pounds-force) and a tensile strength of 4 meganewtons (900,000 pounds-force).
The Class 20E is equipped with a wireless data transmission system, which can send the locomotive operation status, fault data and energy consumption data via GSM and Wi-Fi to a trackside station for analysis. It is also equipped with an axle temperature alarm device, fire alarm system, closed-circuit television (CCTV) system, wheel flange lubricating device and, as personnel safety measure, high voltage protective interlocking devices. The AC traction motors are powered through insulated-gate bipolar transistor (IGBT) control.
Layout
The locomotive has a single cab and a gangway along the centre, while the interior layout and placement of equipment is as follows, from behind the cab towards the rear:
Dual voltage
As on the dual voltage Class 19E, the main electric circuit is automatically selected in either AC or DC mode, based on the voltage of the overhead contact wire feeding the locomotive. To facilitate automatic trouble-free transition on the run, the locomotive is equipped with onboard voltage detectors, while the overhead wire is equipped with two wooden isolators and a 3 metres (10 feet) length of neutral wire, to separate the AC and DC feed. The neutral section is connected to the rails, which serve as the return conductor on electrified lines.
The transition process requires that the locomotive should automatically be switched off before it reaches the isolators and the unpowered overhead wire section, and automatically be restarted after exiting from under the unpowered wire. This is done by a pair of track magnets, one on either side of the neutral overhead wire and spaced 45 metres (148 feet) apart. The two magnets are mounted with their polarities reversed in relation to each other and they activate a magnetic relay, located behind the cowcatcher of the locomotive, to do the switching off and restarting.
Under 25 kV AC/50Hz line voltage, the electric system is designed to operate at a maximum of 31 kV and a minimum of 17 kV, while under 3 kV DC, it is designed to operate at a maximum of 4 kV and a minimum of 2 kV.
Mixed power
The locomotive has regenerative and rheostatic braking, a maximum speed of 100 km/h and is equipped with low-speed controls. Using radio frequency distributed power (RFDP) technology, the units are able to work mid-train in lengthy wagon consists.
A Class 20E unit can also be used as the leading locomotive in multi-unit operation with diesel-electric locomotives.
Pantographs
Transnet Freight Rail insisted that the locomotive should be designed in such a way that the pantograph contact shoe centres are directly above the bogie pivot centres, as was done on the Class 7E and Class 7E2, Series 1 and Series 2. The reason is to reduce the possibility of pantograph hookups on catenary in sharp curves, such as in turnouts, as a result of sideways movement of the pantograph in relation to the overhead wire.
Service
Following testing, the first of the Chinese-built locomotives entered service in March 2014, working on the manganese ore line between Hotazel in the Northern Cape and Port Elizabeth in the Eastern Cape via Kimberley, De Aar and Noupoort.
Two class 20Es, numbers 20-031 and 20-032, were selected to be used on the Blue Train and were painted in blue livery. In Blue Train service they replaced, early in 2015, the previously used Class 18Es on the DC lines and the Class 7Es on the AC lines country-wide.
Illustration
The pictures serve to illustrate the Class 20E from all sides.