Portevin–Le Chatelier effect

Temperature

Temperature affects both the speed of band propagation through the material and the critical strain. The speed of band propagation is proportional to the temperature (lower temp lower speeds, higher temp higher speeds). Often time the critical stain will first decrease due to temperature. The temperature effect on PLC regime is causes by the increased ability of the solutes to diffuse to the dislocations with increasing temperature. Although the mechanism of diffusion is not entirely defined, it is believed that solute atoms diffuse by either volume (high temperatures), diffusion in stacking fault ribbon between partial dislocations (intermediate) or pipe diffusion(low temperature).

Strain rate

While temperature related to rate of diffusion, strain rate determines the time that the dislocations take to overcome these obstacles and have a dramatic effect on the conditions of the PLC effect. So generally the critical stress will decrease with imposed strain rate. Also the higher stress rate the lower the band speed

Precipitates

Often found in Al alloys (especially of the Mg variety) precipitates complicate the PLC effect.

Often these precipitates will cause the so-called inverse behavior which changes the effect of both strain rate and temperature on the solid The Presence of precipitates is shown to have influence on the appearance and disappearance of serrations in the stress strain curve

Grain size

The structure of the material as well has an effect on the appearance and parameters that describe the PLC effect. For example the magnitude of the stress drops is larger with smaller grain. The critical strain often increases with larger grains which is linked to the dependence of the dislocation density to grain sizes Serration amplitude was greater in Al-Mg alloys for finer grain size. There is a correlation between increasing the critical stain and the onset of serration with increasing grain size. But some findings indicate that the grain size has practically no effect on the band velocity or the band width.

Material finish

Polishing the material affects the beginning of the PLC effect and the band velocities that were reported. Apparently a rougher surface provides more nucleation points causing stress raiser which help initiate deformation bands. These bands also propagate twice as fast in the polished specimen

Non effects

The number of vacancies does not directly affect the PLC start point. It was found if a material is pre-strained to a value ½ of that required to initiate jerky flow and then rested at the test temperature or annealed to remove vacancies (but low enough that the dislocation structure is not affected), the total critical strain is only slightly decreased as well as the types of serrations that do occur.

Serrations descriptors

While properties like strain rate sensitivity and critical strain mark the beginning of the PLC effect, people have developed a system to describe the serrations themselves. These types are often dependent on strain rate, temperature, and grain size. While usually the bands are labeled A, B, and C some sources have added a D and E type Bands. Because the type A, B, and C type bands are most found in literature they will be the only ones covered here.

Type A bands

Type A bands are often seen at high strain rate and low temperatures. They are a random development of bands that form over the entire specimen. They are usually described as continuously propagating with small stress drops.

Type B bands

Type B bands are sometimes described as “hopping” bands and they appear at a medium to high strain rates. They are often seen as each band forming ahead of the previous one in a spatially correlated way. The serrations are more irregular with smaller amplitudes than type C.

Type C bands

C bands are often seen at low applied strain rate or high temperatures. These are identified with random nucleated static bands with large characteristic stress drops the serration.

Other notes on band types

The different types of bands are believed to represent different states of dislocation in the bands, and band types can change in a materials stress strain curve. Currently there are no models that can capture the change in band types

Portevin-Le Chatelier (PLC) effect is a proof of non-uniform deformation of CuNi25 commercial alloys at intermediate temperature. In CuNi25 alloy it manifests itself as irregularities in the form of serrations on the stress-strain curve. It proves instability of force during tension and heterogeneity of microstructure and presence of many heterogeneous factors, affecting its mechanical properties.

Problems caused by the PLC effect

Because the PLC effect is related to a strengthening mechanism, the strength of steel may increase; however, the plasticity and ductility of a material afflicted by the PLC effect decrease drastically. The PLC effect is known to induce blue brittleness in steel; additionally, the loss of ductility may cause rough surfaces to develop during deformation (Al-Mg alloys are especially susceptible to this), rendering them useless for autobody or casting applications.