Mill name Mountnessing Mill Operator(s) Essex County Council Type Post mill Year built 1807 Windshaft Cast iron | Mill location TQ 631 979 Purpose Corn mill Phone +44 7904 499106 Auxiliary power Portable engine | |
 | ||
Roundhouse storeys Single storey roundhouse Address Mountnessing, Brentwood CM15 0TD, UK Similar Messing Maypole Mill, Bragg's Mill - Ashdon, Duck End Mill - Finchingfield, Aythorpe Roding Windmill, Stock Windmill | ||
Mountnessing windmill
Mountnessing Windmill is a grade II* listed post mill at Mountnessing, Essex, England which has been restored to working order.
Contents
History
Mountnessing Windmill was built in 1807, replacing an earlier mill. There are records of a windmill here since 1477. The mill was working until 1924, and it worked again in 1932-33.
In 1937, ownership of the mill passed from the Blencowe Estates to Mountnessing Parish Council. It was repaired as a memorial to King George VI, whose coronation was in that year.
Restoration
The mill was restored to working order between 1979 and 1983. A complete new roof was fitted, and the tail of the mill rebuilt. New sails were fitted, and the mill officially opened by Hervey Benham on 13 November 1983. The internal machinery has been rebuilt by Peter Stenning and Richard Seago, and the mill is in full working order.
Description
Mountnessing Windmill is a post mill with a single-storey sixteen-sided roundhouse. The mill is winded by a tailpole. It has four spring sails. There are two pairs of millstones in the breast.
Trestle and roundhouse
The trestle is of oak, with the main post of elm. The crosstrees are 22 feet (6.71 m) long, 13 inches (330 mm) by 10 inches (254 mm) in section. The underside of the lower crosstree is 5 feet 6 inches (1.68 m) above ground level. The main post is nearly 19 feet (5.79 m) in length, 29 inches (737 mm) square at its base. The quarterbars are 13 inches (330 mm) by 10 inches (254 mm) in section. The mill was originally built as an open trestle mill, with a roundhouse added at a later date. Three of the crosstree/quarterbar joints have been strengthened with bolted splints. The sixteen-sided roundhouse is of brick, with a boarded roof covered in tarred felt. It had a thatched roof until 1909, when it was replaced as it was infested with rats.
Body
The body of the mill measures just under 18 feet (5.49 m) by 11 feet (3.35 m) in plan. The crowntree is 22 inches (559 mm) square in section. It receives a 10 inches (254 mm) diameter pintle projecting from the top of the main post. The side girts are 9 inches (229 mm) by 20 inches (508 mm) in section at the ends, thickening to 22 inches (560 mm) at the crosstree.
Sails and windshaft
As originally built, the mill would have had a wooden windshaft and four common sails. The sails are spring sails. The windshaft is of cast iron, replacing the former wooden one. It was probably second-hand when fitted to the mill. It has a mounting for a tail wheel, which would have been forward-facing when fitted; this and other evidence shows that the mill was originally built with a head and tail layout.
Machinery
The wooden brake wheel is of clasp arm construction. It has 77 cogs of 4 inches (102 mm) pitch, driving a wooden wallower with 21 cogs. The cast-iron spur wheel is 3 feet 6 inches (1.07 m) diameter with 66 cogs. It drives the two pairs of millstones underdrift via two 22 inches (559 mm) diameter stone nuts with 32 cogs each. The mill was assisted in its later years by a portable steam engine, which had been built by Wedlake & Dendy Ltd., Engineers of Hornchurch and carried their works number 74.
Millers
References for above:-
Public access
The mill is open to the public on the third Sunday of each month between May and October.