Kalpana Kalpana (Editor)

Hiller VZ 1 Pawnee

Updated on
Edit
Like
Comment
Share on FacebookTweet on TwitterShare on LinkedInShare on Reddit
Top speed
  
26 km/h

Length
  
2.54 m

Manufacturer
  
Wingspan
  
2.13 m

Engine type
  
Reciprocating engine

Number of seats
  
1

Hiller VZ-1 Pawnee Hiller VZ1 quotPawneequot helicopter development history photos


Similar
  
Avro Canada VZ 9 Avrocar, Christmas Bullet, Bell XV 15

The Hiller VZ-1 Pawnee (U.S. Army designation; earlier Army designation: HO-1) was a unique direct-lift rotor aircraft, using contra-rotating ducted fans for lift inside a platform upon which the single pilot shifted body weight for directional control. The platform was developed starting in 1953 under an Office of Naval Research (ONR) contract to Hiller Aircraft, and flew successfully beginning in 1955.

Contents

Hiller VZ-1 Pawnee Hiller VZ1 Pawnee test drive 1955 Photo Story Pinterest

Exploring carla s island on a hiller vz 1 pawnee and de lackner dh 4 aerocycle


Design and development

Hiller VZ-1 Pawnee httpsairandspacesieduwebimagescollectionsf

The original concept had been developed by Charles H. Zimmerman in the late 1940s. Further development followed, both by Hiller Aircraft and the De Lackner Company. There were two main models, the ONR model 1031-A-1, and the somewhat larger VZ-1 Pawnee model produced in 1956 for the U.S. Army. Three of each model were built as prototypes. Neither of the variants was put into production.

Hiller VZ-1 Pawnee Hiller VZ1 Pawnee Wikipedia

The smaller ONR model used two 44 horsepower (33 kW) Nelson H-59 piston engines, coupled to the propellers by a modified helicopter transmission built by the Industrial Power Division of Hall-Scott. The larger Pawnee model used three of the aforementioned engine and had an extended duct area. The Pawnee had ineffective "kinesthetic control" and instead had the operator seated on a platform controlling the flight with conventional helicopter controls.

Testing and evaluation

Due to aerodynamic effects in the duct within which the propellers rotated, the platform was dynamically stable, even though the pilot and center of gravity of the platform were fairly high up. In testing, the prototypes flew well, but the U.S. Army judged them to be impractical as combat vehicles as they were small, limited in speed and only barely flew out of the ground cushion effect.

Hiller VZ-1 Pawnee Hiller VZ1 quotPawneequot helicopter development history photos

Two of the six prototypes are known to survive; both are ONR 1031-A-1 models. One is located at the Hiller Aviation Museum in San Carlos, California, the other is at the National Air and Space Museum's Udvar-Hazy Center in Chantilly, Virginia. The latter platform was formerly on loan to the Pima Air & Space Museum. A replica of the 1031 platform is on display at the Evergreen Aviation & Space Museum.

Specifications (Model 1031-A-1)

Data from National Air and Space Museum and Hall-Scott Motor Company

General characteristics

Hiller VZ-1 Pawnee FileHiller VZ1 Pawneejpg Wikimedia Commons

  • Crew: one
  • Payload: 185 lb (84 kg)
  • Length: 8 ft 4 in diameter (2.54 m)
  • Rotor diameter: 7 ft (2.13 m)
  • Height: 7 ft (2.13 m)
  • Empty weight: 370 lb (167.8 kg)
  • Max. takeoff weight: 555 lb (251.7 kg)
  • Powerplant: × 2 × Nelson H-56 piston engines, 40 hp (30 kW) each
  • Propellers: 2 × contra-rotating two-bladed aluminum
  • Transmission: Hall-Scott helicopter variant
  • Performance

  • Maximum speed: 16 mph (26 km/h)
  • Service ceiling: 32.8 ft (10 m)
  • Armament

  • Standard combat weapons of a U.S. soldier

  • Hiller VZ-1 Pawnee Hiller VZ1 quotPawneequot quotFlying Platformquot Stingray39s List of Rotorcraft

    References

    Hiller VZ-1 Pawnee Wikipedia