Happy Computers

History

Happy Computers was formed in 1982 by Richard Adams under the name Happy Computing. At that time, the 810 Happy was hand wired on the internal side board. The name was changed to Happy Computers or HCI in 1983 when the company went from a sole proprietorship to a corporation. HCI stopped shipping these products in 1990, and since then many other Atari enthusiasts have reverse engineered and replicated the products because they were so popular and fun.

By 1986 software companies began producing fewer titles for the Atari than for the Apple II series or Commodore 64. They attributed this to their belief that an unusually high amount of software piracy existed on the Atari, and cited Happy Drive as a major cause of the piracy.

Atari 8-bit products

This was the first product released in 1982. The customer sent in either their 810 drive or the internal sideboard, and the upgrade was wired in. This consisted of a few extra logic chips, a different eprom and point to point wiring. In addition to the buffered reading and writing with zero latency and faster serial i/o, it made backups of floppies.

This version of the 810 Happy board was a plug-in board with a better data separator and used sockets already in place on the 810 internal board without the need for any soldering or permanent modification. In addition to the buffered reading and writing with zero latency and faster serial i/o, it made backups of floppies.

After the 810, Atari released the more reliable, enhanced density (130 KB) 1050 drive. In addition to the extra storage, the serial I/O could be cranked up a notch even faster than the 810 Happy product by the faster speed of the 1050s 6502 processor. The 1050 Enhancement was also a plug-in board, and could be installed without soldering or permanent modification. In addition to the buffered reading and writing with zero latency and faster serial i/o, it supported true double density (180 KB). The 1050 Controller was a small board that was installed inside the 1050 Happy drive that had 2 switches and an led that allowed enabling or disabling disk write-protect to override the notch in the disk. It also allowed switch selection of a slower mode to provide compatibility with some picky programs. Some commercial software only ran in the original slow speed mode. The controller required a mechanical modification to the drive's enclosure and hence its installation was harder than the happy board.

The software that came with the Happy boards had many options.

This program was included with the Warp Speed Software. It allowed transferring files back and forth between an Atari and an IBM disk using a Happy enhanced 1050 drive. Because the 1050 was a single sided drive with only one head, the disk had to be formatted as SS (180K). The IBM disk could even be formatted on the 1050 drive.

Atari 16-bit products

The Discovery Cartridge was a device that plugged into the cartridge slot of the Atari ST Computer. It backed up floppies and had connectors to allow a 3rd and 4th drive to be hooked up. The original ST computer only allowed for two floppy drives, and the extra drives were handy. There were 4 different options available. Options included a pass through for another cartridge, a switch to bank select larger cartridges, and a switch to select/deselect the extra drives. There was also a battery backed up Time of Day clock option in the Discovery Cartridge, a significant oversight the Atari ST lacked in the stock configuration.

The power of the "HART" chip (Happy Atari Rotating Thing), designed by Richard Adams, allowed standard Atari drives to read the unusual Macintosh variable speed disks without needing a variable speed drive. The disks were then re-written in a standard "constant speed" 3.5 inch compatible format called Magic format. This allowed using the various Mac emulator products that would run most efficiently with Magic format disks. At least one of the Macintosh emulators also had a circuit to read Mac disks, but could make the emulations slower and less reliable. It was faster and more efficient to convert Mac disks to Magic format first.

The HART chip (IC number HARTD1©87HCI) also allowed copying conventional ST disks much faster. The computer floppy controller required two passes per track, three with verification. The HART chip could format and write in the same pass, saving one pass per track.

This was a smaller version of The Discovery Cartridge that plugged into the Atari ST cartridge slot and had a cable for 1 drive that allowed converting Mac disks.