 | ||
A guitar speaker is a loudspeaker – specifically the driver (transducer) part – designed for use in a combination guitar amplifier (in which a loudspeaker and an amplifier are installed in a wooden cabinet) of an electric guitar, or for use in a guitar speaker cabinet. Typically these drivers produce only the frequency range relevant to electric guitars, which is similar to a regular woofer type driver, which is approximately 75 Hz — 5 kHz, or for electric bass speakers, down to 41 Hz&thinsp for regular four-string basses or down to about 30 Hz for five-string instruments.
Contents
The cones of these drivers typically range in size from 6.5 in to 15 in with 10 and 12 in models being the most popular for electric guitar and electric bass combo amps and speaker cabinets. As with all loudspeaker drivers, the magnets are usually made from Alnico, ceramic, or, to reduce weight on more expensive models, neodymium. Higher quality Alnico magnets are reserved for more expensive models. Well-known guitar speaker manufacturers include Jensen, Celestion, Eminence, Electro-Voice, JBL, Peavey, and Vox. Small practice amps often have 6.5 or 8 speakers. Combination (or "combo") amplifier cabinets often have one or more 10 and 12 speakers. The largest speaker "stacks", used in stadium concerts, have eight 10 or 12 in speakers. Bass amplifier speaker cabinets for the bass guitar also often use one or more 10 or 12 in speakers (both 2x10 in and 4x10 in cabinets are popular; in addition, bass cabinets are more likely than electric guitar cabinets to use 15 in speakers.
Guitar speakers are designed differently from hi-fi speakers designed for in-home listening to pre-recorded music; whereas hi-fi speakers are designed to provide as little coloration of the source signal as possible, guitar speakers are often designed to add some type of tonal coloration to the sound.
Cabinet
A guitar speaker cabinet is typically a wooden box that contains one or more guitar speakers. The smallest guitar cabinets have one 6.5" or 8" speaker; these are usually practice amplifier units designed for private practice. Some cabinets designed for rehearsals and small- to mid-size venues contain two 10" or 12" speakers. Another popular format is four 10" or four 12" speakers. Some performers use two 4x10" or 4x12" cabinets. The largest guitar speaker cabinets have eight 10" or 12" speakers. A 4x12" ("four by twelve") is a guitar speaker cabinet containing four 12" speakers. Less commonly, some bass amp cabinets have multiple 8" speakers (e.g., the 8x8" cabinet).
Cabinets with mixed-size speakers are less common, but they are used (e.g., a bass amplifier cabinet with a 15" loudspeaker for lower frequencies and a smaller speaker for mid- to high-range frequencies. A cabinet is usually mono, but may have two inputs for a "stereo" amplifier. Two speakers in a cabinet may be wired in parallel (lowering the impedance) or in series (increasing the impedance). Larger multiples will usually be series/parallel to maintain an impedance of 4 to 8 ohms.
Many cabinets contain parallel input/outputs on the rear panel, so that one speaker cab can be plugged into the amp head, and then a second cabinet can be plugged into the first cabinet; as this "daisy-chaining" approach is wired in parallel, plugging in a second cabinet lowers the impedance. Cabinets typically have an impedance rating printed on the rear panel, such as "8 ohm minimum" or "4 ohms minimum". These warnings mean that the user should not connect an amplifier with a lower impedance of 8 ohms or 4 ohms, respectively. When users daisy-chain a second cabinet, they need to ensure that the speaker and amplifier can handle the lower impedance.
Bass guitar cabinets may include a single speaker (typically 12" or 15"), multiple speakers of the same type (common formats include 2x10", 4x10" and 8x10"). Some bass cabinets use multiple different-sized speakers, such as a mixture of 12" and 15" speakers. In rare cases, some large bass cabinets (known as "bass bins") incorporate folded horns to boost the bass response. Bass amp cabinets may have a horn or tweeter built into a speaker cabinet which contains one or more woofer drivers. When a cabinet has a horn, the enclosure may also have an attenuator knob, for turning the horn volume up or down. Some more expensive bass cabinets with a woofer/horn approach may have additional features, such as circuitry to protect the speakers or horn from overloads or a biamplification option.
Biamplification enables a bassist to use a crossover circuit to split their bass signal into two: a low frequency signal and a high frequency signal, and then route the low and high frequencies into two power amplifiers, each of which send their powered signal to different speaker enclosures. A more powerful power amp amplifies the low frequencies, which are sent the woofer(s), and a less powerful amp amplifies the high frequencies, which are sent to the horn. For bass players seeking a pure, transparent sound, biamplification may produce a "cleaner" sound. For bass players in hard rock or heavy metal who are using an overdriven sound, biamplification may be safer for the horn or tweeter; while a clipped, distorted signal can be handled by a heavy-duty woofer, the same clipped signal may damage a horn or tweeter. Biamping allows a bassist to have the "dirty" overdriven sound through their woofer(s) while keeping the signal sent to the horn clean, thus protecting the horn. At the high onstage volume levels used in large rock and metal concerts, a powerful, overdriven bass signal poses a higher risk of horn damage in non-biamped systems.
Often what is referred to as a "guitar amp" is in fact a combo amplifier: a cabinet with speakers and a built-in amplifier. Combo amplifiers may be referred to by their speaker cabinet configuration plus the word "combo", so that "4x10 combo" means a guitar amplifier built into a 4x10" speaker cabinet. Since the popular configurations are limited in variety, cabinet configurations are often written abbreviated without ambiguity: For example, 4x10" may be written 410, and 112 refers to a single cabinet housing a 12" speaker.
The speaker cabinets, which hold these drivers can be closed-back or open-back, along with variations such as a semi-open back 4x12 in cabinet, which may have a baffle deflecting two of the four speakers. Closed back cabinets may be acoustic suspension or bass reflex. Bass cabinets are usually closed-back or use a bass reflex port or vent to boost low frequency response.
The sound of the speaker and cabinet is crucial to the sound of the electric guitar, so much so that it needs to be considered part of the instrument's tone. If the clean signal from a guitar amplifier or pre-amplifier is captured directly (i.e., before it is sent to a speaker cabinet) it is very brittle and thin, with no resonant depth, particularly from a solid-body electric guitar. A distorted signal captured directly, without going through a speaker cabinet, is even worse: It can sound excessively shrill, scratchy and fizzy, completely different from the smooth tones that listeners hear in recordings or live performances.
When driven hard, guitar speakers produce complex behavior, which affects the sound of the instrument. There will be some power compression, several kinds of distortion, even mechanical limiting as one or more drivers approach their physical limits (e.g. cone excursion). A guitar speaker shows a nonlinear frequency response depending on the speaker's load, e.g. the frequency response at small amplitudes is different from those at large amplitudes.
Isolation cabinets and emulation devices
A guitar speaker isolation cabinet contains a guitar speaker and one or two microphones in a single- or double-layer soundproofed box. These devices allow the capture of the sound of a guitar amplifier and speaker being played loud, while minimizing "bleed through" between tracks in the mix. These are almost exclusively used in recording studios and during live performances that are being recorded.
As an alternative to the isolation cabinet, there are guitar speaker cabinet emulating circuits or signal processors (also known as direct boxes or preamplifier-DI boxes), allowing the sound of a guitar amplifier to be fed directly into a PA system or recording equipment without the need for a speaker cabinet and microphone. Direct boxes are used more often with electric bass than with electric guitar, because the tone of a guitar amplifier and speaker is often considered to be a key element of an electric guitarist's tone. While DI boxes are used to route an electric bass signal to a mixing board, the audio engineer also often uses a mic set up in front of the bassist's speaker enclosure, to capture the bass player's preamped, equalized signal from the speaker cabinet. The engineer can then use either the DI out signal or the miked cabinet in the live or recording mix, or use a blend of the DI signal and the miked cabinet signal.
Digital cabinet emulation is the treatment of a signal with the simulation of the sound of a speaker and a cabinet. It is available in software, "stompbox" pedals and some guitar amps that have a "cabinet modeling" feature. Cabinet emulation is complex, but in its core essence it is the use of digital equalization, which combined with resonance models that reproduce the frequency response of the speaker as well as the internal reflections and standing waves of the cabinet. Cabinet emulators typically offer the user a range of commonly-used presets (e.g., different sizes of speaker cabinet, from small combo amps to large 8x10" "stacks" and different types or styles of speaker or cabinet, for traditional, blues, metal and other genres). Some cabinet emulator systems also allow the user to select the type of miking or the position of the microphones (e.g., front miking, rear miking, etc.).