Device file

Unix and Unix-like systems

Device nodes correspond to resources that an operating system's kernel has already allocated. Unix identifies those resources by a major number and a minor number, both stored as part of the structure of a node. The assignment of these numbers occurs uniquely in different operating systems and on different computer platforms. Generally, the major number identifies the device driver and the minor number identifies a particular device (possibly out of many) that the driver controls: in this case, the system may pass the minor number to a driver. However, in the presence of dynamic number allocation, this may not be the case (e.g. on FreeBSD 5 and up).

As with other special file types, the computer system accesses device nodes using standard system calls and treats them like regular computer files. Two standard types of device files exist; unfortunately their names are, for historical reasons, rather counter-intuitive, and explanations of the difference between the two are often incorrect as a result.

Character devices

Character special files or character devices provide unbuffered, direct access to the hardware device. They do not necessarily allow programs to read or write single characters at a time; that is up to the device in question. The character device for a hard disk, for example, will normally require that all reads and writes are aligned to block boundaries and most certainly will not allow reading a single byte.

Character devices are sometimes known as raw devices to avoid the confusion surrounding the fact that a character device for a piece of block-based hardware will typically require programs to read and write aligned blocks.

Block devices

Block special files or block devices provide buffered access to hardware devices, and provide some abstraction from their specifics. Unlike character devices, block devices will always allow the programmer to read or write a block of any size (including single characters/bytes) and any alignment. The downside is that because block devices are buffered, the programmer does not know how long it will take before written data is passed from the kernel's buffers to the actual device, or indeed in what order two separate writes will arrive at the physical device; additionally, if the same hardware exposes both character and block devices, there is a risk of data corruption due to clients using the character device being unaware of changes made in the buffers of the block device.

Most systems create both block and character devices to represent hardware like hard disks. FreeBSD and Linux notably do not; the former has removed support for block devices, while the latter creates only block devices. In Linux, to get a character device for a disk one must use the "raw" driver, though one can get the same effect as opening a character device by opening the block device with the Linux-specific O_DIRECT flag.

Pseudo-devices

Device nodes on Unix-like systems do not necessarily have to correspond to physical devices. Nodes that lack this correspondence form the group of pseudo-devices. They provide various functions handled by the operating system. Some of the most commonly used (character-based) pseudo-devices include:

Node creation

Nodes are created by the mknod system call. The command-line program for creating nodes is also called mknod. Nodes can be moved or deleted by the usual filesystem system calls (rename, unlink) and commands (mv, rm). When passed the option -R or -a while copying a device node, the cp -l command creates a new device node with the same attributes as the original.

Some Unix versions include a script named makedev or MAKEDEV to create all necessary devices in the directory /dev. It only makes sense on systems whose devices are statically assigned major numbers (e.g. by means of hardcoding it in their kernel module).

Naming conventions

The following prefixes are used for the names of some devices in the /dev hierarchy, to identify the type of device:

Some additional prefixes have come into common use in Linux-based systems:

The canonical list of these prefixes can be found in the Linux Device List, the official registry of allocated device numbers and /dev directory nodes for the Linux operating system.

For most devices, this prefix is followed by a number uniquely identifying the particular device. For hard drives, a letter is used to identify devices and is followed by a number to identify partitions. Thus a file system may "know" an area on a disk as /dev/sda3, for example, or "see" a networked terminal session as associated with /dev/pts/14.

On disks using the typical PC master boot record, the device numbers of primary and the optional extended partition are numbered 1 through 4, while the indexes of any logical partitions are 5 and onwards, regardless of the layout of the former partitions (their parent extended partition does not need to be the fourth partition on the disk, nor do all four primary partitions have to exist).

Device names are usually not portable between different Unix-like system variants, for example, on some BSD systems, the IDE devices are named /dev/wd0, /dev/wd1, etc.

devfs

devfs is a specific implementation of a device file system on Unix-like operating systems, used for presenting device files. The underlying mechanism of implementation may vary, depending on the OS.

Maintaining these special files on a physically implemented file system (i.e. harddrive) is inconvenient, and as it needs kernel assistance anyway, the idea arose of a special-purpose logical file system that is not physically stored.

Also defining when devices are ready to appear is not entirely trivial. The 'devfs' approach is for the device driver to request creation and deletion of 'devfs' entries related to the devices it enables and disables.

DOS, TOS, OS/2, and Windows

A device file is a reserved keyword used in DOS, TOS, OS/2, and Microsoft Windows systems to allow access to certain ports and devices.

DOS uses device files for accessing printers and ports. Most versions of Windows also contain this support, which can cause confusion when trying to make files and folders of certain names, as they cannot have these names. Versions 2.x of MS-DOS provide the AVAILDEV CONFIG.SYS parameter that, if set to FALSE, makes these special names only active if prefixed with DEV, thus allowing ordinary files to be created with these names.

GEMDOS, the DOS-like part of Atari TOS, supported similar device names to DOS, but unlike DOS it required a trailing ":" character (on DOS, this is optional) to identify them as devices as opposed to normal filenames (thus "CON:" would work on both DOS and TOS, but "CON" would name an ordinary file on TOS but the console device on DOS). In MiNT and MagiC, a special UNIX-like unified filesystem view accessed via the "U:" drive letter also placed device files in "U:DEV".

Using shell redirection and pipes, data can be sent to or received from a device. For example, typing TYPE c:data.txt > PRN will send the file c:data.txt to the printer.