Place of origin Indonesia Wars UNIFIL | Used by See Operators Designer Pindad | |
 | ||
Type Armoured personnel carrier In service 2009–Present (Indonesian service) | ||
The Anoa is a 6x6 armoured personnel carrier developed by PT Pindad of Indonesia. The vehicle is named after the Anoa, which is a type of buffalo indigenous to Indonesia. The prototype was first unveiled at the 61st anniversary of TNI on October 5, 2006 in TNI HQ at Cilangkap, east of capital Jakarta. The Anoa resembles the French VAB, which is also in service with Indonesia.
Contents
History
The Anoa had been officially unveiled to the public under the designation APS-3 (Indonesian: Angkut Personel Sedang, English: Medium Personnel Carrier) at the Indo Defence & Aerospace 2008 exhibition on November 19, 2008 to November 22, 2008 after being shown in a TNI parade on October 5, 2008. On August 30, 2008, 10 APS-3s have been produced with the plan of having 150 vehicles to be produced for the Indonesian Army in time for their first deployment in 2009.
20 of the Pansers were handed over to the Indonesian government through the Defense Ministry, part of a deal from the initial 150 vehicles to 40 due to the economic crisis. 40 Pansers were delivered as part of PT Pindad's commitment to the total delivery of 154 Pansers. 33 Pansers were eventually submitted to the Ministry of Defence on January 13, 2010. Pindad had received loans from state-owned Bank Mandiri, Bank BNI 46 and Bank BRI as part of payments for the manufacture of the Pansers.
The Anoas were officially placed into Indonesian military service on July 2009. They were publicly seen in service with the Mechanical TNI Battalion Task Force Garuda Contingent in Lebanon.
The Anoa made its first appearance overseas when it was publicly display in BRIDEX 2011 in Brunei. It was also displayed at DSA 2012 in Malaysia where a planned Malaysian-only marketed Anoa called the Rimau was unveiled to the public.
Development
The development history of the Pindad Panser was started in 2003 as a result of increased military intervention in the Aceh province. During the conflict, the Indonesian Army put forward urgent requirements for an armored personnel carrier for the transport of troops.
Pindad responded to this requirement in 2004, with the APR-1V (Angkut Personel Ringan) a 4x4 armored vehicle based on a commercial Isuzu truck chassis. 14 vehicles were built by Pindad and were sent to Aceh for evaluation and combat trials. However, the follow-on orders for another 26 vehicles were canceled following the 2004 tsunami.
Pindad continued the APC development program with assistance from the Agency For Assessment and Application of Technology or BPPT in 2005. The next prototype was the APS-1 (Angkut Personel Sedang), a 6x6 design that was again based on a commercial Perkasa truck platform by PT Texmaco. Although it was not selected for production, the experience gained in developing the APS-1 convinced the Indonesian Army to give the go-ahead by Pindad to develop the next generation of Panser vehicles, the APS-2 at a production cost of US$600,000 each.
Design
The APS-3 differed from its predecessors which had been based on commercial truck platforms. Instead, the "Anoa" used a monocoque hull design consisting of armor steel. The steel was made by PT. Krakatau Steel to NATO standards to STANAG Level III standard in withstanding 5.56 and 7.62 mm bullets. A new torsion bar suspension system was also developed for the Panser. The engine and transmission are imported from Renault with a Renault MIDR 062045 six-cylinder turbo-charged diesel engine with ZF S6HP502 automatic transmission fitted. Transmission consist of six forward gears and one reverse.
The crew enters the front compartment through two side doors. The driver sits on the right side of the vehicle while the vehicle commander sits on the left. Two additional hatches in the roof provide emergency exits for driver and commander. The gunner sits behind commander inside the weapon turret. The engine is located behind the driver, while the left side of the vehicle is fitted with weapon turret. All of the windows are bullet-proof and also further protected by armored shutters, which can be shut entirely, leaving a small observation slit for vision. An armoured hydraulic ramp door at the rear provide access to the troop compartment. Two inward-facing, benches provide seating for 5 troops each. Communications equipment include VHF / FM (anti-jamming and hopping) and GPS with night vision equipment included. Emergency exits are present on both sides of the Anoa as well as three roof hatches in the troop compartment with one rear-facing machine gun mounting on the right cupola. A video camera was also fitted at the rear of the vehicle to help driver while reversing the vehicle.
Anoa-2
The Anoa-2 was officially revealed to the public in Indodefence 2010. It is equipped with optional waterjet propellers for the ability to swim in shallow water. It is also equipped with an optional RWS machine gun of unknown caliber, possibly 7.62 mm. The RWS is controlled remotely from inside the Anoa.
Visual differences from the first generation of the Anoa include rounded roof cupolas and the re-position of the smoke grenade launchers from the sides of the vehicle to directly in front of the driver and commander cupolas. Modification to the windows armored shutters which in previous version of Anoas required one to open and close them from the outside manually. Redesign of vehicles exhaust system from previously rounded muffler with long exhaust pipe into rectangular muffler with short exhaust pipe. Reduction of side windows in troop compartment from 4 for each side into 3. Modification of troop compartment featuring individual roof/wall mounted blast protection seat for 8 troops. Some vehicle also fitted with camera featuring night-vision capabilities at the front of the vehicle.
Badak FSV
A fire-support version using a CMI Defence's CSE-90 turret with the Cockerill 90 mm Mk III was first unveiled at Indo Defence & Aerospace 2008, which was announced that the APS-3 fire-support version would be deployed into the Indonesian Army by 2010. The final, definitive version of the fire support variant was unveiled at Indo Defence & Aerospace 2014 as the Badak. The Badak featured a new all-welded monocoque steel hull with STANAG 4569 Level 3 protection, a new 340 hp power pack located front left and the driver seated towards the front on the right side, leaving the remainder of the hull clear for the installation of the turret. The suspension also utilizes double wishbone independent suspension (as opposed to torsion bar on the Anoa) for better stability while firing the 90mm canon. The CMI Defence CSE 90LP two-person turret has a baseline protection of up to STANAG 4569 Level 1 (upgradable to Level 4) and is armed with a 90mm low-pressure rifled gun. In addition, there is a 7.62mm co-axial machine gun, with another 7.62mm machine gun mounted on the left side of the turret roof for use in the self-defence and air defence roles, plus banks of 76mm grenade launchers.
Armament
The baseline vehicle is fitted with a cupola on the left of the vehicle and armed with a 12.7mm (.50 cal) heavy machine gun or a 40 mm automatic grenade launcher. In Indo Defence & Aerospace 2010, the Anoa 2 was shown to the public with a RWS installed.
Variants
The following variants are produced by Pindad: